IEC Industrial platinum resistance thermometers and platinum temperature sensors. The International Standard that specified Industrial PRT’s since has been IEC IEC Ed.2 introduces several significant technical changes with . Buy IEC Ed. Industrial platinum resistance thermometer sensors from SAI Global. STANDARDS. SUBSCRIPTIONS. Content Management Software.

Author: Tohn Kagazil
Country: Canada
Language: English (Spanish)
Genre: Finance
Published (Last): 12 June 2014
Pages: 295
PDF File Size: 15.2 Mb
ePub File Size: 16.29 Mb
ISBN: 215-1-28870-197-5
Downloads: 66117
Price: Free* [*Free Regsitration Required]
Uploader: Tekus

Learn how your comment data is processed. This would be displayed as follows this is an example only Calibration Temperature Thermometer Reading The standard specifies 4 classes of accuracy. As we discussed earlier, stzndard may not actually need the accuracy at this point, but rather the repeatability. If you need to know only, “Is it hot or is it not? People often mistake this for the total accuracy of the system, but that is a mistake! Then you need to spell out your requirements for the applications engineer.

From our previous calculations we know that at the standard calibration temperature points we offer, our own Pt with a Class B probe would normally have the following accuracy uncertainties. Hi Santhu, It is just a case of accuracy. To ensure this standarx, the single ice point calibration acceptable for Class B sensors will not suffice.

There are four primary temperature scales in use today. Aside from these cases, it is generally better to state your requirements in terms of temperature tolerance in degrees over the temperature range where it is actually required. If you cross reference the temperature you are likely to be measuring and add them to the tolerance of the Pt unit you can calculate which Class of probe will be suitable for your application.

It is more practical to look the application. The uncertainty of measurement for the thermometer is. The International Electrotechnical Commission IEC has published the second edition of its standard on industrial platinum resistance thermometers and platinum temperature sensors.


Pt RTD Colour codes IEC

Lubricant Storage and Handling. So which is right? This one is nice and simple, but often misunderstood. The IEC therefore states in section 4. The minimum and maximum temperatures of the stated working range are conve-nient points to chose and will ensure Class A accuracy, but will at the same time tend to drive up the 6051 of the sensor.

The Best Gets Better: Subscribe Today Reliable Plant Newsletters. The specification was poorly written.

ATP Instrumentation Ltd

This site uses Akismet to reduce spam. But remember, when specifying a Class A RTD, you must always include the working range at which it must perform to this accuracy.

This is the number you will most commonly see listed in product descriptions. In the examples below we used our own Pt model. Each probe has a different level of tolerance. The uncertainty of the unit The uncertainty of the probe Uncertainty of any calibration procedure So lets break it down. The standard also defines the relationship between temperature and stanfard electrical resistance of the thermometer, allowing for the replacement of sensors independent of their manufacturers.

Although conforming to the use of a 0. Build Processes That Drive Consistency. Calibration is a fantastic tool for eliminating the known uncertainty that comes with every instrument.

Temperature is one of the most frequently used parameters in industry, and accuracy in its measurements is critical standwrd the chemical, pharmaceutical, metal, and food sectors.

The Calibration Temperature — This is the temperature the thermometer is being tested at The Pt Thermometer reading — This is the reading the Pt thermometer gave at this known temperature The uncertainty remaining at the calibrated temperature points.


It stsndard important to understand that just like K-Type thermometers there are 3 main areas of uncertainty when using Pt thermometers. How to Integrate Demand-driven Planning with Maintenance. The table below shows the tolerances of each Class of probe at various temperatures. But as the temperature increases, so does the permissible deviation due to the variations possible in the TC.

IEC revises standard on thermometers and sensors

Platinum resistance thermometers are among the most accurate temperature sensors, and are relatively immune to electrical noise, making them particularly well suited for industrial environments.

These are IEC designations of accuracy. Conversely, not all applications require even Class B accuracy.

Because a well manufactured RTD will have high repeatability relative to the applicationClass B accuracy is generally sufficient unless there is a need for better interchangeability; or when measuring change of temperature; or if you know that you have special accuracy requirements. Each probe has the capacity to drift away from this curve reducing accuracy.

This is the accuracy of the device that actually interprets the signals from the probe and displays your reading. Let’s take the freezing point of water in Celsius for example.

Not only does this informs the user of any adjustments to idc made to the reading at the desired temperature. Specific changes in the new edition include: Toggle navigation Toggle search. This is not unrealistic for a well-made RTD, although it requires special selection of the sensing element at this temperature. Live Temperature Sensor Support.

Author: admin