Don’t forget about our other 2Wire HG-G info that you might be interested in. Login to 2Wire HG-G Router · Change your 2Wire HG-G IP Address. You might find additional types of support and download options at your service provider’s website. For example, a search for “2Wire” at AT&T’s. Rec’vd my 2wire hg-b and the DSL light is green but will not connect to Internet (Internet light is red or off) I have my username.
|Published (Last):||12 November 2015|
|PDF File Size:||9.36 Mb|
|ePub File Size:||2.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Configuration parameters for modules listed in the Advanced Link Manager States page. DMZplus can only be configured for one computer on your home network at a time.
Configure the Wireless Network Page I would try and power the modem from another circuit before replacing. Please enter a valid email address. Page 19 Default Gateway Part of the Internet address settings.
When in stealth mode, the 2Wire gateway firewall does not return any information in response to network queries; that is, it will appear to the hacker who is trying to access your network that your network does not exist.
Changing Timeout Parameters The MTU Maximum Transmission Unit is the largest size packet or frame, specified in octets eight-byte bitsthat can be sent from 2eire computer to the network.
Add Definition Repeat the previous step for each port or range of ports required for the application profile.
Software version The current 2Wire gateway software version. Home Network Tab To set up a private network: Edit Firewall Settings Page From the pull-down menu, select the computer that you wish to host the application.
The link groups that display are dependent on the 2Wire gateway model.
Compliance Information The 2Wire HG product family has been tested, and is compliant to the following standards: Enter text from picture: Page 45 Repeat these steps for each port or range of ports required for the application profile. The default WEP key is located on the bottom of the gateway, next to the serial number.
A numeric identifier for your computer. The max point reward for answering a question is Page 55 Not a start session packet — drop packet. Strict Udp Session Control Strict UDP instructs the 2Wire gateway to be more restrictive about what packets are allowed to transmit over an established connection from a local network computer to the Internet.
2Wire HG-B Default Password & Login, Manuals and Reset Instructions | RouterReset
Page To perform a ping or traceroute test: Advanced – Syslog Settings Page The Advanced – Syslog Settings page allows users to maintain a history of security events greater than the capacity of the 2Wire gateway by enabling a syslog server. The Local Network — Status page includes the following information: Do you still have questions concerning the router that you can’t find online? Try the following site: Maximum rate achievable at the time of the 2701ng-b connection based on the line quality specifically, the uncapped rate.
The radio frequency band the access point uses for your wireless network the default is 6. Att works with the username 7201hg-b password type of authentication but charter requires the MAC address of modem for authentication. Management and Diagnostic Console Reviewing Bitloading The Bitloading pane shows the bits loaded per tone for the upstream tones 6 to 31 and downstream tones 32 mnual spectrum.
2Wire 2701HG-G User Manual
Router error page displays in the gateway user interface if the gateway detects the presence of a third-party router. Subnet Mask The subnet mask allocated to the 2Wire gateway. The link is functioning properly. Page 77 Ethernet home network interface, the number of payload bytes received, 2wie the number and percentage of received packets in error.
But yes in case charters has username and password authentication and works with the telephone jack in house then its possible to use the same modem. I’ve got the same issue, 2 wire claims mamual whrn the power light is red, the modem is bad and must be replaced. Node Information Description Link status Up.
Manually Configure AT&T HG-B – 2Wire | DSLReports Forums
Ethernet home network interface, the number of payload bytes received, and the number and percentage of received packets in error. To ensure that the settings cannot be changed, in the Password field enter a password.
IP address for example, Upstream Rate The speed at which data goes over your broadband connection from your network to the Internet, measured in kilobits per second kbps.
Modifying the settings on this page can impact the ability of computers on the local network to access the broadband connection. These time settings are displayed in the Current Time Settings 2aire, which shows the current date, time, time zone, and whether the time was automatically or manually configured.
Management and Diagnostic Console button in the Broadband Link field allows you to reset the 2Wire gateway broadband link. Troubleshooting – Resets Page If the feature is not enabled, an error message will display when you click the link to access this page. Log information is stored in an 8 KB buffer. Your can reset your 2Wire HG-B in the following way s:. A specification for connecting multiple computer users on an Ethernet LAN to a remote site through common customer premises equipment such as a modem.