ASTM A311 PDF

(Identical to ASTM Specification A /A M (R) except for deletion of , revision of Table 1 footnote A, and editorial corrections to Table 2.) 1. A Class B Stressproof TG&P Cold Finished Bar Round Turned Ground Polished, A Round Bar, A Rod, A TG&P Rod, A TG&P Round Rod . See the chemical composition and physical properties of ASTM A Grade cold-drawn, stress relieved, annealed bar, find alternative materials, and.

Author: Zolomuro Vudole
Country: Albania
Language: English (Spanish)
Genre: Technology
Published (Last): 5 March 2005
Pages: 442
PDF File Size: 9.96 Mb
ePub File Size: 5.70 Mb
ISBN: 849-9-71946-341-3
Downloads: 11996
Price: Free* [*Free Regsitration Required]
Uploader: Tygotilar

The bars are furnished in two classes, A and B. Atm LaSalle is exceptionally responsive to the needs of our customers and puts a high priority on providing uniformity in the machinability of our products in order to improve productivity for you.

A Steel Bar | Capital Steel & Wire

Within the text, the SI units are shown in brackets. NOTE 2— When turned bars are speci? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not astj as part of the standard.

This abstract is a brief summary of the referenced standard. Therefore, a warpage test is always performed on the first bar drawn through either a new or reground die. The heavy draft stress-relieved Class B came into aastm with the release of the specification.

The yield strength shall be determined at 0. Link to Active This link will always route to the current Active version of the standard.

ASTM A311 Grade 1117 cold-drawn, stress relieved, annealed bar

This specification covers cold-drawn, stress-relieved carbon steel bars subject to mechanical property requirements. The cast or heat analysis shall conform to the chemical composition requirements specified. Routine warpage tests are also conducted throughout the life of the die. Materials and Manufacture 6.

Mechanical property testing is always the final operation after all processing is completed. One class, B, is cold drawn with higher than normal heavy drafts to provide higher strength levels, and four grades provide improved machinability.

  KURT ROSENWINKEL ROUND MIDNIGHT PDF

Have questions about your specific products? Details of these requirements shall be agreed upon between the manufacturer and the purchaser. One class, B, is cold drawn with higher than normal heavy drafts to provide higher strength levels, and four grades provide improved machinability. Although it also can be induction hardened, it should be watched for quench cracks. Warpage tests are also regularly made as part of a standard quality assurance procedure.

A311 Steel Bar

Workmanship, Finish, and Appearance You can rely on Niagara LaSalle for all of your steel bar needs. Adtm is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The results then become an integral part of the quality assurance program. To further improve quality, Niagara LaSalle reduced the standard seam depth tolerance for StressProof from 0.

Niagara Lasalle Steel Products – Stressproof ®, ASTM A, Cold Rolled Steel Round Rod

aetm For continuous type of treatment, a lot shall consist of 25 tons [25 Mg] or less of the same size of each heat, treated in the same cycle. Niagara LaSalle developed this groundbreaking process in and forever changed the economics of part production.

NOTE 1— A typical ordering description is as follows: If restraightened, then the same number of tests are again required. Within the limits of good manufacturing and inspection practices, the bars shall be free of injurious seams, laps, segregation, or other imperfections that, due to their nature, degree, or extent, will interfere with the use of the material in machining or fabrication of suitable parts.

  FINANCE D ENTREPRISE PIERRE VERNIMMEN PDF

Resulfurized steels are not subject to inclusion ratings. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. The report shall include the name of the manufacturer, ASTM designation and year date and revision letter, if any, class and grade, heat number, size, and grain size if requested. Parts you are now heat treating from Rc 23 to Rc Combining values from the two systems may result in nonconformance with the specification.

The area of the sample to be examined should be agreed upon between the purchaser and the manufacturer, and the test specimen should be hardened by heating and quenched before being polished to avoid pits. Restricted Cast or Heat Analysis the surface of the material.

The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. Click below to make an inquiry. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Referenced Documents asttm, and then cooling slowly enough to minimize the development of new residual stresses.

One warpage test is taken of first bar produced by a new or reground specialty designed drawing die.

The stress relieving temperature selection is based on 60 years of experience aa311 thorough documentation. Seams deeper than that stated above are rejected. The primary melting may incorporate separate degassing or re?

The importance of high temperature stress relieving to obtain maximum ductility, minimum warpage and excellent machinability is a major part of the original patent.

Author: admin