AKM 5381 PDF

ASAHI KASEI. [AKD].. / – 7 -. [ADC Plot: fs=48kHz]. AKM. AK THD+N vs. Input Level. VA=VD=V, fs=48kHz, fin=1kHz. AKM Semiconductor AKET. Explore Integrated Circuits (ICs) on Octopart: the fastest AKET. Dual Channel Dual ADC Delta-Sigma 96ksps bit. The AK achieves high accuracy and low cost by using Enhanced dual bit ∆Σ WARNING: AKM assumes no responsibility for the usage beyond the.

Author: Mezikree Vigul
Country: Sri Lanka
Language: English (Spanish)
Genre: Finance
Published (Last): 14 September 2011
Pages: 25
PDF File Size: 13.94 Mb
ePub File Size: 5.1 Mb
ISBN: 996-6-23083-139-2
Downloads: 95686
Price: Free* [*Free Regsitration Required]
Uploader: Maulkis

AKM assumes no responsibility for the usage beyond the conditions in this datasheet.

Профессиональные аудио-интерфейсы и их конвертеры (ЦАП/АЦП) | Manifold Studio

This value is the full scale 0dB of the input voltage. A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. The power up sequence between VA and VD is not critical. If these clocks are not provided, the AK may draw excess current due to its use of internal dynamically refreshed logic.

Voltage Reference The voltage input to VA sets the analog input range. Before considering any use or application, consult the Asahi Kasei Microsystems Co. The cut-off frequency of the HPF is 1. In master mode, the internal timing starts when MCLK is input. An analog initialization cycle starts after exiting the power-down mode. Alternatively if VA and VD are supplied separately, the power up sequence is not critical. Lead frame surface treatment: Date Code Marketing Code: The audio interface supports both master and slave modes.

  FSV CONFIGURATION IN SAP PDF

In slave mode, the internal timing starts clocking by the rising edge falling edge at mode 1 of LRCK after exiting from reset and power down state by MCLK. The reference frequency of these responses is 1kHz. Operation at or beyond these limits may result in permanent damage to the device. Input voltage is proportional to VA voltage.

An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. The digital filter rejects noise above the stop band except for multiples of 64fs. No load current may be drawn from these pins. Normal operation is not guaranteed at these extremes. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board.

The ADC outputs settle in the data corresponding to the input signals after the end of initialization Settling approximately takes the group delay time. VA and VD are usually supplied from the analog supply in the system. AKM sales office or authorized distributor concerning their current status.

All digital input pins should not be left floating. Decoupling capacitors should be as near to the AK as possible, with the small value ceramic capacitor being the nearest. All voltages with respect ak ground. The AK requires no external components because the analog inputs are single-ended.

  BRYCE COURTENAY TANDIA PDF

The AK includes an anti-aliasing filter RC filter to attenuate a noise around 64fs. The AK samples the analog inputs at 64fs. Resolution 24 Aim Input Voltage Note 4 2. The passband and stopband frequencies scale with fs.

Grounding and Power Supply Decoupling The AK requires careful attention to power supply and grounding arrangements. Table 1 shows the relationship of typical sampling frequency and the system clock frequency. This time is from the input of an analog signal to the setting of 24bit data both channels to the ADC output register for ADC.

Профессиональные аудио-интерфейсы и их конвертеры (ЦАП/АЦП)

The input signal range scales with the supply voltage and nominally 0. This reset should always be done after power-up. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high 53381 of performance and reliability. An electrolytic capacitor 2. The calculated delay time induced by digital filtering.

All signals, especially clocks, should be kept away from the VCOM pin in order to avoid unwanted coupling into the AK

Author: admin